114D – Batch Controller
$1,595.00 Excl. GST
All prices are in NZ$, and GST exclusive and are subject to change without notice.
Product Details
The Model 114D Batch Controller is designed for flow applications where the precise control of batch quantities is required. Batch Total, Accumulated Total and Pre-set values can all be displayed on the large LCD display.
The 114D has an input conditioning circuit which will accept pulse or frequency flow signals generated by turbine, positive displacement, paddlewheel or other flowmeters.
Configurable link positions enable the input circuit to be configured for the different signal types.
This item is DC powered with a battery backup. The 114D will operate from an external power source between 9 and 28 Volts and draws no more than 4mA. Lithium batteries provide backup if the DC power is interrupted so that totals are not lost. The solenoids or sensors, however, may still require external power.
Solid state outputs provide control to solenoids and relays, and can sink up to 200mA.
114D Features
- Displays Batch Total, Accumulated Total and Preset
- One or two stage valve control
- Watertight to IP67 (Nema 4X)
- Wall or Pipe, Panel mounting
- Fully programmable
- CE Compliant
Technical Specs
| 114D Batch Controller Specifications | ||
| General | ||
| Display | LCD which is continuously powered | |
| Batch Total | 7 digits with 10mm (0.4") high digits | |
| Accumulated Total | Displayed when the ACCUM TOTAL button is pressed | |
| Preset | 5 digits with 8.5mm (0.33") high digits | |
| K-factor | The pulses per unit of measure (eg. pulses/gallon) is programmable in the range 0.0001 to 999,999 | |
| Decimal Points | Decimal point position is fully programmable for the total and preset | |
| Frequency Range | 0Hz to 10kHz | |
| Signal Type | Link settable for sinewave (15mV P-P minimum), open collector, reed switch, pulse or Namur proximity switch | |
| DC Power Input | 9-28 Volt at 4mA maximum | |
| Battery Backup | ||
| Type | The two Lithium cells are 3.6V, AA types. e.g. TADIRAN SL360/S, SAFT LS14500EX Note the battery polarity when replacing | |
| Battery Life | 2 years typical | |
| Outputs | ||
| Outputs | Two solid state relay outputs suitable for driving DC solenoids or external relays | |
| Switching Power | 200mA. 30VDC maximum | |
| Supply Backup | Lithium battery | |
| Isolation | Both outputs are separately isolated via optoisolators | |
| Physical | Physical | Physical |
| Temperature | Operating temperature: -20°C~60°C | |
| Dimensions | 98mm (3.9") high x 152mm (6.0") wide x 43mm (1.7") deep (cable glands not included) | |
| Protection | Sealed to Nema 4X or IP67 standards | |
| Cable Entry | By cable glands | |
| Material | Polycarbonate and ABS | |
| Wall Mounting | Universal mounting bracket supplied as standard |
Documents
- Contrec 114D Batch Controller - Data Sheet 174.39 KB
- Contrec 114D Batch Controller - Manual 636.63 KB
Related Products
OM Series
Oval Gear Flow MetersIn stock
$0.00 Excl. GST
Select options
This product has options that may be chosen on the product page
DP Series
Flow MetersIn stock
$0.00 Excl. GST
Select options
This product has options that may be chosen on the product page
Similar Products
RT14
Flow Rate TotaliserIn stock
$1,133.00 Excl. GST
Select options
This product has options that may be chosen on the product page
RT40
Flow Rate TotaliserIn stock
$0.00 Excl. GST
Select options
This product has options that may be chosen on the product page
IN-RT
Flow Rate Indicator With TotaliserIn stock
$578.00 Excl. GST
Select options
This product has options that may be chosen on the product page
