Intech Wind direction Vane WD-CL
WD-CL $910.00 Excl. GST
Back to products
Intech Pyranometer Light Sensor LE-CL
LE-CL $555.00 Excl. GST
Intech Anemometer Wind Speed Transmitter WS3-CL - 3 Cup
Intech Anemometer wind speed transmitter WS6-CL
Anemometer Wind Speed Assembly Diagram WS3-CL
wind speed
Click to enlarge
Intech Anemometer Wind Speed Transmitter WS3-CL - 3 Cup
Intech Anemometer wind speed transmitter WS6-CL
Anemometer Wind Speed Assembly Diagram WS3-CL
wind speed

WS3(6)-CL – Wind Speed Sensor (Anemometer)

Brand:

$910.00 Excl. GST

Wind Speed 3 Cup with 4~20mA output (1.5m/sec start, 20mA = 60m/sec)

Wind Speed 6 Cup with 4~20mA output (0.45m/sec start, 20mA = 80m/sec)

Total: $910.00

All prices are in NZ$, and GST exclusive and are subject to change without notice.

Product Details

Description

The WS-CL Anemometer is a highly responsive three or six cup anemometer that produces an output pulse with a frequency proportional to the wind speed. This pulse is then processed and converted for suitable communications. The Anemometer is made from stainless steel and anodized aluminium. Stainless steel shafts, bearings, and fittings are used throughout.

The three or six cups on the head have been hand balanced to provide precision balancing of the cup assembly on the shaft. This instrument has been thoroughly tested before leaving the factory and is ready to be installed.

The Anemometer can be supplied with a Pulse (switch closure) or 4 to 20mA Output.

The 3 Cup Anemometer WS3-CL is normally supplied but if low speed accuracy is required we also manufacture a 6 Cup version WS6-CL.

It can be supplied free standing on a Base Mounting Plate (as picture above), or attached to a L Bar or T Bar Equipment Mounting Arm.

This unit can also be added to one of our Fully Mounted Weather Stations or our Small and Medium Weather Systems.

WS3(6)-CL Features

  • Range: 0~60m/s for 3 Cup and 0~80m/s for 6 Cup
  • Accuracy ±2%
  • Start speed: 1.5 m/s for 3 Cup and 0.45m/s for 6 Cup
  • Cable length: 5 metres

Technical Specs

TYPEWS3(6)-CL
Common Specifications:
Accuracy±2%.
Resolution0.2m/sec.
Time From Power To Output Stable3 Seconds.
Cable5m, UV resistant.
Range                     3 Cup:0~60m/sec (216Km/hr.)
                              6 Cup:0~80m/sec (288Km/hr.)
Wind Speed Average Time3 Seconds.
Start Speed             3 Cup:1.5m/sec.
                              6 Cup:0.45m/sec.
Operating Temperature-5°~60°C.
(Anemometer may stop turning due to freezing below 0°C.)
EMC CompliancesEmissions EN 55022-A. Immunity EN 50082-1.
Safety CompliancesEN 60950.
Dimensions            - OverallH=180mm, CupØ=150mm.
                            - Mounting PlateL=70mm, W=38mm, H=6.5mm, PCD=55mm.
Current Output Specifications:
Output4~20mA, 2 wire (Loop Powered).
Load Resistance600Ω @ 24Vdc.
Voltage Output Specifications:
Output0~5Vdc, 3 Wire (common ground)
Power Supply Required12Vdc.
RS485 Output Specifications
OutputRS485
Baud Rate9600.
Format8 Bit, No Parity, 1 Stop Bit (non selectable).
ProtocolMODBUS RTU.
USB Output Specifications:
OutputUSB (Std Male Type A, 5Vdc Powered).
Baud Rate9600.
Format8 Bit, No Parity, 1 Stop Bit (non selectable).
ProtocolMODBUS RTU.
Pulse Output Specifications:
OutputPulse: 12Vdc @15mA Max.
                              3 Cup:2 pulses per metre of wind.
                              6 Cup:3 pulses per metre of wind.

Documents