- Controller in 1 with input 3 points, setting 3 points, and output 3 points.
- Can make CH2 and CH3 follow CH1.
- Can select program function (optional).
- Can select event output (optional).
- Can select remote setting input (optional).
- Can select analog output (optional).
- Can select communication function (optional)
- Has simple dustproof drip-proof structure.
MR13 – 3 Input/Output Controller
The MR13 is a 3 channel controller with simultaneous 3-channel display.
Features
- 3-channel controller, 3-channel input, 3-channel setting and simultaneous 3-channel display
- Accuracy: ± (0.3% FS + 1 digit)
- Follow-up type PV input function
- Follow-up type SV setting function
- Remote/local and DI input function
- Programmable 1 pattern with 9-step function
- Expert PID which gives remarkably improved PID control efficiency; overshoot and undershoot are controlled effectively
- Interface RS232C/RS485
Brand: SHIMADEN
Usually in stock
Request a quoteScroll down for product range
Display | |
LED display | PV display 7-segment LED green 4 digits 3 channels to be displayed individually.
SV display 7-segment LED orange 4 digits CH display 7-segment LED orange 1 digit |
Action display LED |
Control output display: 3 – OUT1, OUT2, OUT3 Auto tuning: 1 – AT Follow type SV display: 1 – FLW Program RUN: 1 – RUN Event output display: 3 – EV1, EV2, EV3 Remote input display: 1 – REM Communication display: 1 – COM |
Display accuracy | ±(0.3%FS + 1 digit) Standard accuracy |
Temperature range in which accuracy is maintained | 23°C±5°C |
Display resolution | Depends on measuring range (0.001, 0.01, 0.1, 1) |
Sampling cycle | 0.5 seconds |
Measured value display range | –10% to 110% of measuring range |
Setting | |
Setting | By 6 front key operation |
Setting range | Same as measuring range |
Higher/lower limit setting limiter | Higher and lower limits to be set separately; free within measuring range (Lower limit < higher limit) |
Follow type SV setting | SV of CH2 or CH3 can be set to follow CH1 (deviation setting) (on condition that measuring range of CH2 or CH3 is the same as that of CH1.) |
Input | |
Input type has to be the same for 3 channels (measuring rangecan be selected individually). | |
Thermocouple | B, R, S, K, E, J, T, N, PL II, WRe5-26, {L, U (DIN43710)} (Multiple input, multiple range. Refer to measuring range code table.) |
External resistance | 100Ω maximum |
Input impedance | 500kΩ minimum |
Burnout | Standard feature (up scale) Cold junction temperature compensation accuracy: ±2.0 °C (5~45 °C) |
R.T.D | JIS Pt100/JPt100 3-wire type (Multiple range. Refer to measuring range code table.) |
Amperage | Approx. 0.25 mA |
Lead wire tolerable resistance | 5Ω maximum/wire |
Voltage | ±10, 0~10, 0~20, 0~50, 10~50, 0~100mV DC, or ±1, 0~1, 0~2, 0~5, 1~5, 0~10V DC (Multiple input, programmable range. Refer to measuring range code table.) |
Input impedance | 500kΩ minimum |
Current | 4~20, 0~20mA DC (Multiple input, programmable range. Refer to measuring range code table.) |
Receiving impedance | 250Ω |
Sampling cycle | 0.5 seconds |
PV bias | ±1999 units |
PV filter | OFF, 1~100 seconds |
Follow type PV input | PV input of CH2 or CH3 can be set to follow CH1 (deviation setting) (on condition that measuring range of CH2 or CH3 is the same as that of CH1.) |
Isolation | Insulated between input and various outputs (not insulated between input and system, remote input and DI input) |
Control | |
Control mode | Expert PID control with auto tuning function |
Proportional band (P) | OFF, 0.1~999.9%FS (OFF=ON/OFF action) |
Integral time (I) | OFF, 1~6000s (OFF=P, PD action with manual reset) |
Derivative time (D) | OFF, 1~3600s (OFF=P, PI action) |
Manual reset | ±50.0% |
ON/OFF hysteresis | 1~999 units |
Proportional cycle | 0.5~120.0 seconds (0.5 sec. is unit for setting.) |
Control output characteristics: | RA/DA selectable (set to RA when shipped) |
Output limiter | Higher limit, lower limit 0.0~100.0% (lower limit < Higher limit) |
Soft start | OFF, ON (Fixed to 10 sec.; Valid when power is turned on, RTS RUN, and when returned from scaleover.) |
Control output/rating | |
Output specification has to be the same for 3 channels. | |
Contact output (Y) | 1a 240V AC 2.5A/resistive load |
Current output (I) | 4~20mA, 0~10mA DC/load resistance 600Ω maximum. |
SSR drive voltage output (P) | 15V±3V DC/Load current 20mA maximum |
Voltage output (V) | 0~10V DC/Load current 2mA maximum |
Operation output updating cycle | 0.5 second |
Isolation | Insulated between control output and system and input (not insulated between control output I, P or V and analog output) |
Event output (optional) | |
Number of outputs | 3 -EV1, EV2, EV3 (Selectable from CH1, CH2 and CH3, individual setting, individual output) |
Output rating | Contact output 1a (common) 240V AC / 1A (resistive load) |
Setting | Individual setting
0) NON: Not assigned |
Hysteresis | 1~999 units (when DEV or PV has been selected) |
Standby action | Selectable (when DEV or PV has been selected) |
Action delay time | OFF, 1~9999 seconds (when DEV or PV has been selected) |
Isolation | Insulated between alarm output and various inputs/outputs and system |
Remote setting (optional, selectable between this function and DI) | |
Setting signal | 1~5V, 0~10V, 4~20mA |
Setting range | Same as measuring range |
Accuracy of setting | ±(0.3%FS + 1) digit |
Channel for setting | Selectable from CH1, CH2 and CH3 |
Remote scaling | Within measuring range (inverted scaling possible) |
Remote bias | –1999~5000 units |
Remote filter | OFF, 1~100 seconds |
Sampling time | 0.5 second |
Isolation | Insulated between remote input and various outputs (not insulated from system and various inputs) |
External control input (DI) (optional, selectable between this function and remote setting) | |
Number of input point | 1 |
Input rating | Non-voltage contact, open collector input (about 5V/0.4mA DC impress) |
Action type | NON, FLW (follow type SV), RST/ RUN, HLD and ADV |
Isolation | Insulated between DI input and various outputs (not insulated from system and various inputs) |
Program (optional) | |
Registrable pattern | 1 |
Number of steps | 9 maximum |
Program setting range | |
Level | Same as measuring range |
Time | 1~9999 minutes/step |
Ramp | To be set automatically according to level and time |
Number of executions | 9999 maximum |
PID output limiter | To be set selectively from 3 types of PID & output limiter |
External control input | DI/non-voltage 1 point (RUN/RST, HLD, ADV) |
Action status output | RUN, END and STEP to be selectively output to event output |
CH2 and CH3 in SV follow setting | Program to be executed by making CH2 or CH3 deviation-follow to pattern set in CH1 in SV follow setting. Not in SV follow setting, program is executed in FIX mode. |
Additional functions | Temporary suspension (HLD), carryforward (ADV), PV start Analog output (optional, selectable between this function and communication) |
Number of output | 1 |
Output types | Selectable from CH1_PV, CH2_PV, CH3_PV, CH1_SV, CH2_SV, CH3_SV, CH1_OUT, CH2_OUT and CH3_OUT |
Output rating | 0~10mV DC/Output impedance 10? 0~10V DC/Load current 1mA maximum 4~20mA DC/Load resistance 300? maximum |
Output accuracy | ±0.3%FS (to displayed value) |
Output resolution | Approx. 1/8000 |
Output updating cycle | 0.5 seconds |
Output scaling | Within measuring range (inverted scaling possible) |
Isolation | Insulated between analog output and various inputs and system (not insulated between analog output and control outputs I, P and V) |
Communication (optional, selectable between this function and analog output) | |
Communication type | RS-232C, RS-485 |
Communication system | Half duplex start-stop synchronous system |
Communication speed | 1200, 2400, 4800, 9600, 19200bps |
Data format | 7 bits, 8 bits, no parity, even parity selectable |
Communication address | 1~99 |
Communication code | ASCII code |
Communication protocol | Shimaden standard protocol |
Communication format | Control code selectable, BCC check arithmetic system selectable |
Isolation | Insulated between communication signal and system/input/output |
Others | Meets the EMC standards with an additional clamp filter (E04SR301334, SEIWA Information Systems Co.,LTD) |
Others | |
Data storage | By non-volatile memory (EEPROM) |
Ambient temperate/humidity ranges | -10~+50°C/below 90% RH (on condition that there is no dew condensation) |
Temperature for storage | Between-20 and +65 °C |
Power voltage | 100V~260V AC ±10% (50/60 Hz) |
Power consumption | 12VA maximum |
Input noise removal ratio | Normal mode 45 dB minimum (50/60 Hz) Common mode 140 dB minimum (50/60 Hz) |
Applicable standard Safety | IEC1010-1 • EN61010-1 EMC EMI (emission): EN50081-2: 1993 EMS (immunity): EN50082-2: 1995 |
Insulation resistance | Between input/output terminals and power terminal: 500V DC 20MΩ minimum Between input/output terminals and protective conductor terminal: 500V DC 20MΩ minimum |
Dielectric strength | 1 minute at 2300V AC between input/output terminals and power terminal (inductive current 5mA)
1 minute at 2300V AC between power terminal and ground terminal (inductive current 5mA) |
Protective structure | Only front panel has simple dustproof and drip-proof structure |
Material | PPO resin molding (equivalent to UL94V-1) |
External dimensions | 96 x 96 x 110 mm (Panel depth: 100 mm) |
Mounting | Push-in panel (one-touch mount) |
Panel cutout size | H92 x W92 mm |
Weight | Approx. 420 g |
ITEMS | CODE | SPECIFICATIONS | ||||||||
SERIES | MR13- | MPU-Based 3 Channel Auto-Tuning PID Controller DIN 96 × 96mm | ||||||||
INPUT | 1 | Thermocouple B, R, S, K, E, J, T, N, PLII,
WRe5-26, U, L |
Multi-input Multi-range |
|||||||
2 | R.T.D. Pt100 / JPt100 | Multi-range | ||||||||
3 | Voltage (mV) -10-10, 0-10, 0-20, 0-50, 10-50, 0-100mV DC | Multi-input Programmable Range | ||||||||
4 | Current (mA) 0-20, 4-20mA DC | |||||||||
6 | Voltage (V) -1-1, 0-1, 0-2, 0-5, 1-5, 0-10V DC | |||||||||
CONTROL OUTPUT | -Y | Contact: Proportional Cycle 0.5-120.0 sec. Contact capacity: 240V AC 2.5A / resistive load | ||||||||
I1- | Current: 4-20, 0-10mA DC Load resistance: 600Ω max | |||||||||
P1- | SSR drive voltage: Proportional Cycle 0.5-120.0 sec. Output rating: 15V±3V DC / 20mA max | |||||||||
V1- | Voltage: 0-10V DC Load current: 2mA max. | |||||||||
PROGRAM FUNCTION (OPTION) | N | None | ||||||||
P | 1 Pattern, 9 step | |||||||||
EVENT OUTPUT (OPTION) | 0 | None | ||||||||
1 | Contact (1a common): 240V AC 1A / resistive load EV1, EV2, EV3 / 3 Point | |||||||||
REMOTE OR DI INPUT (OPTION) | 00 | None | ||||||||
04 | 4-20mA DC Receiving resistance: 250Ω | |||||||||
05 | 1-5V DC Input resistance: 500kΩ min. | |||||||||
06 | 0-10V DC Input resistance: 500kΩ min. | |||||||||
51 | DI Non-Voltage Contact, Open Collector Input | |||||||||
ANALOG OUTPUT OR
COMMUNICATION FUNCTION (OPTION)
|
00 | None | ||||||||
03 | Voltage 0-10mV DC, Output resistance: 10Ω | |||||||||
04 | Current 4-20mA DC, Load resistance: 300Ω max | |||||||||
06 | Voltage 0-10V DC, Load current: 1mA max | |||||||||
15 | RS-485 | |||||||||
17 | RS-232C | |||||||||
REMARKS
|
0 | Without | ||||||||
9 | With (Please consult before ordering.) |
MR13 Controllers are Shimaden Lite Software Compatible – Software Available “Free”
Product Range
Code | Specifications | Price | Quantity | ||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
MR13-2Y1-N0 | RTD Input with Contact Output | $960.00 | |||||||||
MR13-2Y1-N1 | RTD Input, Contact Output + Events | $1,080.00 | |||||||||
Intech Instruments Ltd are the New Zealand distributor for Shimaden products. Please contact the Shimaden distributor in your country if you require sales or service support for Shimaden products.
Not sure what you need? Ask us anything!